Free shipping in the Northeast & Mid-Atlantic3-Year Craftsmanship WarrantyCall or text (888) 474-9876

Free shipping in the Northeast & Mid-Atlantic

Resources

Can You Insulate It? Yes — Here's How

Questions? Ask our Buyer's Guide, or call or text (888) 474-9876.

Yes — and if you'll spend real time in your building, insulate the roof and the floor. Solid wood — walls run 3/4–1 3/4 in (19–44 mm) depending on model — already buffers temperature well, and on its own a small heater takes the chill off on cool days. Want more than that? Do the cheap, high-impact step first, then insulate where it actually counts.

A cozy reading corner inside a solid-wood garden cabin on a winter day

First, Seal the Drafts

Sealing gaps and drafts around doors, windows and the base is the biggest comfort gain per dollar on any small building. Do this before you spend a cent on insulation — it's quick, cheap, and you'll feel the difference immediately.

How to Find and Seal Them

  • The door first. Most drafts come from here. Check that it closes evenly onto its weatherstrip; if it doesn't, turn the hinges in or out a little — it's the one adjustment they have — and re-check it once or twice as the walls settle.
  • Then the windows. Close each opening window onto its seal and look for daylight around the edges.
  • Daylight between wall boards? Something is holding the wall up — usually a shelf, frame or bracket screwed across several boards. Loosen it and let the wall settle back down. Don't fill the gap.
  • Never caulk or foam the wall joints, or the gaps above the doors and windows — they're how the walls settle. If you ever need to stop a draft there, tuck in something soft that squashes, never anything rigid.

Insulate the Floor

Insulation sits between the floor joists as the floor goes in, with the floorboards on top and an optional plywood or OSB subfloor in between (not needed on the Isla, whose floorboards are thicker; skip it on the Cove and Vale — their interior doors only clear the kit's own floor). It's far easier during assembly than later, so plan for it up front. The exact build-up varies slightly with your foundation.

Fitting insulation boards between the floor joists over a vapor barrier

Two ways to build it

On a solid surface — a concrete slab, pavers or a gravel pad: lay a vapor barrier sheet over the base, set the pressure-treated beams and joists as your manual shows, fill between the joists, add an optional plywood or OSB subfloor (not needed on the Isla; not on the Cove or Vale), then the floorboards.

Raised on a timber frame, blocks, piers or ground screws: first close the underside so the insulation has something to sit on — plywood, or a breathable membrane stapled under the joists — then fill between the joists and lay the floor. Keep the airflow under the building open.

Insulate the Roof

Add a grid of 1×2, 2×3 or 2×4 battens on top of the roof boards, pack insulation into the cavities, then sheathe it all with plywood or OSB and fit your roof covering. A deeper batten means thicker insulation. Floor and roof together do most of the work.

Insulating a gable roof: foil-faced foam boards fitted between battens on the roof boards, with plywood sheathing screwed on top

The Roof Edge and the Extra Weight

A roof build-up makes the roof edge thicker by the depth of the battens plus the sheathing. If the roof-edge trim from your kit no longer covers it, swap in a wider trim board, bought locally. Every layer also adds weight. In heavy-snow areas, screw the battens through the roof boards into the roof beams, not just into the boards: lay them right above the beams, or run them down the slope across them. From above, the rows of nails or screws in the roof boards show where the beams run; the beam ends also show at both ends of the roof until the fascia boards go on. Keep the build-up as light as you can, and call us before you start if you're unsure.

What to Use

Pick insulation that copes with a little moisture: rigid foam boards (XPS, EPS or foil-faced polyiso) or mineral-wool batts. Rigid foam is easiest in the roof — cut it to fit snugly between the battens; laid on edge, 1×2, 2×3 and 2×4 battens hold roughly 1½, 2½ and 3½ in. In the floor either works: support batts from below so they can't sag, and close the underside with a breathable membrane or mesh to keep critters out.

Why We Say Leave the Walls

There's no stud frame: the walls are solid stacked logs, and the timber itself is the insulation — the thicker the wall, the better it insulates. Our walls are 1 3/8 in (34 mm) on the Aria and Luna and 1 3/4 in (44 mm) on the Thea, Vela, Neva, Isla, Cove and Vale; the glass-fronted Mira has wood wall panels with 3/4 in (19 mm) boards. The walls also settle in their first 12–18 months and then breathe with the seasons, so they stay solid wood, inside and out — no insulation, no cladding. Sealed drafts, an insulated floor and roof, and a heater: that's the whole recipe.

Heat It

A 500–1,500 W electric panel heater is plenty for most rooms; a mini-split adds cooling and gives you comfortable heating and air-conditioning year-round. A wood or pellet stove is a bigger step: it usually needs a permit, the wall clearances and non-combustible floor pad its manual specifies, and a chimney through the roof — check with your building department and insurer, and ask us before you cut the roof.

Keep It Dry Inside

A heated room in cold weather collects moisture — from people, plants, even a kettle. Open a window or a vent for a few minutes each day, and never use an unvented propane or kerosene heater inside: an electric panel heater or a mini-split keeps the air dry and safe.

Plan the Wiring Now

Running power? Do it before the floor and roof are closed in — cables can run under the floor or through the roof build-up instead of across the walls. Anything that climbs a wall goes in flexible conduit, so the wall can still settle. See our Electrical Guide.

Floor and roof insulation, sealed drafts and a heater comfortably carry a solid-wood building through the seasons. In the coldest northern states, choose a model with 1 3/4 in (44 mm) walls and size your heater for your winters — the walls themselves are never insulated.

Common Questions

Can I insulate after the building is up?
Plan it before you build. We recommend fitting the roof covering within 24–48 hours of assembly, and roof insulation has to go on before it — the next chance is when you re-roof. The floor is far easier during the build, because the insulation sits between the joists under the floorboards.
Can I use spray foam?
Not on the walls — it bonds to the wood and stops it moving. In the floor and roof, rigid boards or batts are simpler and easy to take out later.
Does insulation change the height?
The roof gets thicker by the depth of your battens and sheathing. The floor stays where it is — the insulation sits between the joists.
Do I need a vapor barrier?
Under the floor on a solid surface — a slab, pavers or a gravel pad — yes. In the roof, follow the insulation maker's instructions for your climate.

Stuck on your project?

Ask our Buyer's Guide, or call or text us — real people who know every model, happy to talk you through any step.

(888) 474-9876
From kit to cabin
Review us on: