Choosing Your Roof Covering
Questions? Ask our Buyer's Guide, or call or text (888) 474-9876.
Your kit includes the tongue-and-groove roof boards. The weatherproof layer that goes on top is chosen separately, so you can match your climate and the look you want. The right choice starts with one thing — your roof's slope — because a covering that's perfect on a pitched roof will leak on a low-slope one.

If Your Roof Is Pitched (Apex)
- Asphalt shingles — the American standard: durable, widely available, a 15–30-year roof, and the classic cabin look. Our default for pitched roofs. US building code allows asphalt shingles only on roofs of at least 2:12 (with double underlayment up to 4:12) — which is why they're not used on our low-slope models.
- Metal / standing seam — the longest-lasting (40+ years). Sheds rain and snow beautifully and looks sharp on modern models, at a higher upfront cost. It's also the loudest in rain and hail, because the roof boards are your ceiling — a sound-deadening underlayment, or insulation above the roof boards, quiets it a lot.
- Roofing felt (underlayment) — the base layer that goes beneath every covering except an EPDM membrane (shingles, metal and roll roofing alike), and a temporary cover that keeps the roof dry until they go on. It isn't a finished roof on its own. Where winters bring heavy snow, consider a self-adhesive ice-and-water membrane (rated ASTM D1970) along the eaves, where melting snow can refreeze into ice dams and push water back under the shingles. On a pitch between 2:12 and 4:12, a single layer of it can also stand in for the double felt.
Pitched roofs: Aria, Thea, Neva, Cove, Vale


If Your Roof Is Low-Slope (Pent / Flat)
On a shallow pitch, shingles aren't the answer — water can work its way back under them. You want a sealed, watertight surface instead:
- Asphalt roll roofing — the simple, budget option for low-slope roofs; like shingles, it goes on over roofing felt.
- EPDM rubber membrane — the go-to, and what we recommend for our low-slope models: one seamless sheet with no joints for water to find, long-lived, low-maintenance and the quietest in rain. To lay it: sweep the roof boards clean and tap down any raised nail heads; unroll the sheet with spare at every edge and give it about half an hour to relax; fold back one half, roll the adhesive onto the boards and smooth the sheet down from the middle outward, then repeat on the other half; fold the corners rather than cutting them, finish the edges with drip edge or edge trim, and check that rain runs off the low side, clear of the walls.
- PVC roof panels — a durable, lightweight alternative.
- Metal — works on a low slope too, but only in a standing-seam profile rated for low slopes (most screw-down panels need a steeper roof), and it's louder in rain than EPDM.
Low-slope roofs: Luna, Vela, Mira, Isla


At a Glance
| Covering | Roof type | Typical lifespan | Good to know |
|---|---|---|---|
| Asphalt shingles | Pitched | 15–30 years | The US standard; laid over an underlayment with a drip edge |
| Metal / standing seam | Pitched (low-slope profiles for low-slope roofs) | 40+ years | Sheds snow best; higher upfront cost; loudest in rain |
| Roofing felt (underlayment) | Pitched or low-slope | Temporary only | The base layer beneath every covering except EPDM — not a finished roof |
| Asphalt roll roofing | Low-slope | About 5–10 years | The budget low-slope option |
| EPDM rubber membrane | Low-slope | 20+ years | One seamless sheet, bonded to the roof; quietest in rain |
Lifespans are typical ranges — check the manufacturer's rating for the product you buy.
Underlayment and edges. Under every covering except EPDM — shingles, metal or roll roofing — lay a roofing underlayment over the roof boards first, and fit a metal drip edge along the eaves and gables so water drips clear of the walls. EPDM is the one exception: the membrane goes down in one sheet, bonded straight to the roof boards with no felt beneath, and is finished with edge trim. If you choose to insulate the roof, do it before the covering goes on — see our Insulation Guide.

Nail Length: Your Roof Boards Are Your Ceiling
From inside, the tongue-and-groove roof boards are your ceiling, so fasteners that go too deep show through. Our roof boards are 5/8 in (16 mm) thick. Use the shortest nails or screws your covering's instructions allow for that thickness. With shingles laid straight onto the roof boards, the tips can still just show inside; if that bothers you, add a layer of plywood or OSB — or your roof insulation — first, and fix the covering into that.

How Much to Buy
Your model's roof area is listed in the Roof line of its Specifications. Add about 10% for trimming and waste. Shingles are sold in bundles — usually three to a “square” of 100 sq ft; membranes and roll roofing by the roll; metal panels cut to your exact lengths.
Gutters?
Optional, but worth it when the building sits close to a fence, a path or another building: a small gutter, with the downspout led away from the base, keeps splash-back off the bottom wall boards and water away from your foundation.
Whatever You Choose
We recommend fitting the covering within 24–48 hours of assembly to protect the boards. Follow the covering manufacturer's instructions — including their minimum-slope rating. Pitched (apex) roofs: Aria, Thea, Neva, Cove and Vale. Low-slope (pent) roofs: Luna, Vela, Mira and Isla. The roof covering isn't included in the kit — you buy it locally, which lets you match it to your climate and local look.
Snow. In heavy-snow areas, a pitched roof — Aria, Thea, Neva, Cove and Vale — sheds snow more easily than a low-slope one, and a metal covering helps it slide off. On our low-slope models — Luna, Vela, Mira and Isla — clear heavy snow after a big storm with a roof rake from the ground — never climb onto a snowy roof.
Common Questions
- When should the covering go on?
- As soon as the roof boards are down — ideally the same day; we recommend within 24–48 hours of assembly. Until then, keep a tarp over the roof.
- Can I walk on the roof?
- Carefully, on a dry day, stepping over the roof beams. Use a proper ladder and fall protection on anything steep — or hire a roofer for the covering.
- Should a roofer do it?
- If you're not comfortable working at height, yes. A small roof is a quick job for a local roofer: share your model's roof area (it's in the Roof line of its Specifications) and the covering you've chosen.
- Insulating the roof?
- It goes on before the covering — see our Insulation Guide.
Stuck on your project?
Ask our Buyer's Guide, or call or text us — real people who know every model, happy to talk you through any step.